Top 10 common forklift mishaps ， forklift operation should take note of these matters ！.

Top 10 common forklift mishaps ， forklift operation should take note of these matters ！.

Blog Article

Do not underestimate the forklift at the workplace. If the operation is not good, there will be significant crashes in minutes, and there are many mishaps involving forklifts.

Situation 1: The forklift freight blocked the motorist's sight, and the person ahead might not be located, causing a rolling accident.
Situation 2: In order to maintain the balance of the forklift when raising heavy products, the workers used their body weight as the weight, which virtually created casualties.
Situation 3: The size of the forklift cargo goes beyond the permitted width of the route and hangs on the roadside shelf, which nearly triggers an accident.
Case 4: Forklift is speeding and rolls over during a turn.
Case 5: The forklift motorist did not see the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift lifts the employees illegally, the forklift motorist does not put on the safety belt, the forklift lifter falls and the vehicle driver is crushed when the forklift surrender.
Instance 7: The forklift chauffeur did not use a seat belt and fell from the lorry when it rolled over and was crushed.
Forklift procedure ought to pay attention to these issues ：.

Beginning.
1. Before beginning, observe the surroundings, and after confirming that there are no challenges that impede the safety and security of driving, beep the horn initially and afterwards begin.
2. For automobiles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic stress ( atmospheric pressure) scale need to be safe before starting.
3. When the forklift starts with a load, the vehicle driver must first confirm that the load is steady and reputable.
4. The beginning needs to be slow-moving and steady.

Driving.
1. When driving, the height between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast should be tilted in reverse. .
2. Do not lift the fork expensive when driving. When entering and leaving the job website or while driving, beware that there will certainly be no challenges overhead. When the tons is taking a trip, the fork must not be raised too expensive, which will affect the security of the forklift. .
3. After dumping, the fork should be lowered to the normal driving position before driving. .
4. When transforming, if there are pedestrians or automobiles close by, the driving signal needs to be released initially. High-speed sharp turns are restricted. High-speed sharp turns will certainly create the vehicle to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly forbidden to switch off the flame and slide, and it is prohibited to brake suddenly while driving with lots unless there are unique scenarios.
6. When the forklift is running, it must obey the website traffic rules in the factory and should keep a specific security range from the lorry in front. .
7. When the forklift is running, the lots needs to be in the lowest placement that does not hinder the driving, and the gantry must be correctly tilted back. The load will not be elevated other than when piling or filling. .
8. The height of the tons need to not block the driver's sight. In unique situations, when the thing impacts the forward vision, drive at a reduced rate when reversing.
9. It is forbidden to switch on the ramp, neither to drive across the ramp. .
10. The secure driving rate of the forklift in the factory location is 5 km/h, and it has to drive safely at a low speed when going into the production workshop location. .
11. When the forklift is raised, raised or driven, it is prohibited for personnel to depend on the fork to hold things and play a stabilizing function. .
12. If issues are located, they will be repaired and reported in a timely fashion, and they will never operate with ailments or conceal them.

filling and dumping.
1. When fork-loading things, the distance between the two forks need to be readjusted as needed to make the load of the two forks balanced and not skewed, and one side of the product ought to protest the shelf. .
2. It is prohibited to work with a solitary fork or use a fork top or pull. In special situations, safety and security indication need to be set up to remind surrounding pedestrians. .
3. In the process of packing and unloading things, the forklift must be stopped with the brake. .
4. The rate of the automobile must be slow-moving and constant. Take care not to roll the wheels on the dunnage, so as not to extend the rolled items and hurt people. .
5. When using a fork to fork the goods, the fork ought to be as deep as possible under the tons, and it must be noted that the fork suggestion should not touch other products or items. The load needs to be stabilized with minimal back tilt of the gantry to make sure that the load does not move backwards. The mast can be tilted forward slightly when the lots is decreased to permit easy placement of the load and removal of the forks. .
6. It is forbidden to fork items at high speed and hit tough items with the fork head. .
7. When the forklift is functioning, it is forbidden for individuals to stand around the fork, so as to stay clear of the collapse of the goods and hurt individuals. .
8. Overwhelming is forbidden, and it is restricted to make use of forks to lift employees to participate in high-altitude procedures to stay clear of high-altitude dropping crashes. .
9. It is not allowed to utilize the brake inertia to slide, place, round or roll things. .
10. It is not allowed to make use of forks to pick, transform pallet dump.

Leaving .
1. It is restricted to leave the forklift when the items on the fork impend. Prior to leaving the forklift, you should discharge the goods or reduced the fork frame.
2. Draw the emergency brake manage to dead or depress the emergency brake switch.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the automobile's line of vision and does not surpass 1 minute).
4. Remove the trick. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the look should be checked, and gas, lubing oil and cooling water must be added.
2. Inspect the safety and security performance of beginning, running and braking.
3. Examine whether the Electric Forklift Truck for Warehouse lights and horn signals are full and efficient.
4. During the operation of the forklift, check whether the stress and temperature level are regular.
5. After the forklift is running, the external leak must additionally be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You have to inspect before leaving the car;.
2. When you run into somebody in front of you during driving, you must send a signal at a distance of 5 m;.
3. The driving speed in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be as well sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no activating the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the automobile should be driven in reverse when going downhill;.
8. When the forklift employees carry the goods and move on, if they experience huge or heavy items and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be complied with in the procedure.
1. Single fork operation is not permitted.
2. It is not allowed Stand-on Electric Pallet Stacker to lift the goods for cross country driving.
3. It is not allowed to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and various other dangerous chemicals with forks.
5. It is not permitted to make use of inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not allowed to bring people to work with the pallet or fork, and it is strictly forbidden to stand under the fork after the fork is increased.
8. Do not drive side to side on inclines
.
Vehicle parking is not allowed under the list below conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an challenge on one side of the road, the contrary side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844